Главная 7 Aquarium 7 Silent Aquarium Compressor

Silent Aquarium Compressor

maintenance, care, compatibility

Silent aquarium compressor: how to select and install

The answer is obvious to everyone who has seen this device in operation: it increases the oxygen content in aquarium water. Water in a stationary state may eventually turn into a kind of swamp.

And, as a result, to the disease, and in the worst case to the death of the inhabitants of the aquarium. The compressor, feeding air into the water, enriches it with oxygen, creates streams of air and water.

This process is called aeration, and such compressors are sometimes referred to as aerators. Simply put, this is an air pump.

Silent aquarium compressor installation is quite simple. The external aerator must be placed on the shelf or directly on the glass cover of the aquarium so that the length of the hose allows for aeration from the bottom up.

That is, the end of the spray hose (if any) was as close as possible to the bottom of the tank. Sprayer is advised to use to ensure that air bubbles are as small as possible.

In this case, the process of enriching the aquatic environment with oxygen is more intensive.

Some models of household silent compressors for an aquarium are supplied with suckers. This is very convenient, as the aerator can be securely attached directly to the glass wall of the fish house.

Of course, you must have a nearby power source (sockets).

It should be noted that the concept of noiseless with respect to aquarium compressors is a bit incorrect. It is more correct to call them quiet, since any of these air pumps produce a certain level of noise during operation.

There are two types of aquarium compressors. In a piston aerator, air is pushed out by a piston.

This unit is characterized by high performance, durability, but the noise level in it is quite high. The second type of aquarium compressors – membrane. The air in it is supplied through membranes, working only in one direction.

Such an aquarium air compressor is relatively silent and consumes little power. But its power will not be enough for a large aquarium.

The choice of a silent compressor for an aquarium depends on the size of the tank with water, as well as on the required depth of air supply. Experts advise when choosing an aquarium compressor to take into account such a calculation: the aerator should have a capacity of about half a liter of air per hour, designed for one liter of water.

For smaller aquariums, the compressor is considered one of the most silent ones. JBL ProSilent a100, which has a built-in silencer, so its work does not prevent people from resting in the room. This diaphragm compressor comes with a check valve, a spray bottle and a two-meter hose.

Popular silent model of the compressor is the aerator of the Chinese company Triton. This two-channel aerator can provide reliable circulation of water and air in an aquarium with a capacity of up to 170 liters.

Another silent compressor manufacturer is a German company. Eheim – together with the aerator offers high-quality sprayers and hoses.

Ukrainian company Collar produces small and easy-to-use silent compressors of the brand. aPUMP. This aerator is able to work successfully in a stitle tank at a depth of 80 cm.

If you could not buy a compressor that would suit you in terms of noise level, you can make such a silent aerator yourself.

An air pump or compressor is an apparatus that provides aeration of water, enriching it with dissolved oxygen. For a home aquarium, this is a necessary device, since the glass pond is a closed space in which all fish and plants may lack oxygen. In the natural environment, water is saturated with oxygen during the movement of water.

At night, the plants pass oxygen, and release CO2 (carbon dioxide). Not always enough plants in order to provide the fish with oxygen, for their full life you need a compressor.

In the compressor there are tubes for oxygen supply – through them it enters the water. Air pressure is regulated by special valves and clamps.

To effect aeration of the aquarium, several nozzles must be attached to the air tubes, which are usually made of an abrasive substance or a white grinding stone. Being at the bottom of the aquarium, the sprayers emit a lot of air bubbles, creating a beautiful decorative effect.

These bubbles are very fond of guppies, danios, neons, scalar and mollies.

The smaller the size of the bubbles, the greater their total area, which is favorable for intensive aeration of the reservoir. Aquarium pump you need to choose a powerful (from small bubbles – strong pressure). Air bubbles at the surface burst, resulting in the destruction of the bacterial film, and there is an improvement in aeration.

In addition, the bubbles mix all layers of water, aligning its temperature in the aquarium.

See how to install the compressor in the aquarium.

The compressor for the aquarium are of two types: piston and membrane. If you want to choose an aeration device that makes little noise, then a piston compressor will do.

When you need multiple compressors, you can choose two types at once – piston and diaphragm. The first can be included at night, the second – in the daytime.

To avoid strong noise, you can put foam rubber under the compressor. Otherwise, you will have to move the device to another room and take it to the aquarium using a strong air duct.

However, this risk requires a very powerful reservoir.

You can choose a membrane compressor if you want to save electricity in the house. Such a device is allowed to be connected at once to several aquariums, it has a long service life, it does not need to be repaired often. The disadvantage of such a device is that it makes a lot of noise.

Unfortunately, there are no silent compressors – their principle of operation is based on vibration. The compressor, which is under water, will not be so noisy, but it will work around the clock.

You can put the aquarium in a separate room, where no one sleeps – then you can connect a membrane aerator to it.

The aquarium pump will help to create coordination of air flows in tanks of different capacities, and will help to carry out water supply to the filter, also is the driving element of a filtration. The pump has 2 functions – it saturates water with oxygen and cleans it.

If you have a large aquarium, it is advisable to purchase a pump that will help ensure the circulation of water in the pond, which is very useful for all its inhabitants. This device does not make a lot of noise, because it is placed in the water, not outside.

If you are not satisfied with the quality of branded aquarium compressors, you can do it yourself. However, such a device will work well only if you have the skills to create such mechanisms.

Self-made compressors can cause a short circuit in water, which is very dangerous for life. Waterproofing in this case – a very necessary part of the aerator.

See how to make a compressor with your own hands.

COMPRESSOR FOR THE AQUARIUM AND EVERYTHING THAT IS NECESSARY TO KNOW ABOUT THIS.

The answer is obvious to everyone who has seen this device in operation: it increases the oxygen content in aquarium water. Water in a stationary state may eventually turn into a kind of swamp.

Remains of vital activity of small fish, grain of feed, dust, small debris, film on the surface, lack of oxygen can all lead to an unfavorable state of the aquatic environment.

And, as a result, to the disease, and in the worst case to the death of the inhabitants of the aquarium. The compressor, feeding air into the water, enriches it with oxygen, creates streams of air and water.

This process is called aeration, and such compressors are sometimes referred to as aerators. Simply put, this is an air pump

.The main requirements that must be placed on the device when choosing it

Often the aquarium is in the same room where people relax. Therefore, for the aquarium it is better to choose a silent compressor.

This device operates continuously. To reduce the noise level of the device, you can remove it into the cabinet. But then you need too long duct.

Therefore, it is worth thinking carefully before making the compressor silent, by isolating it. It is better to purchase a silent device at once. The air compressor for the aquarium is the most silent.

Compressors should have a smooth adjustment of the air flow. Such a device can be easily adjusted to a different number of filters and nozzles.

Compressor capacity is calculated on the basis of the following parameters: 0.5 l / h per 1 l of water. This is the way to solve the question of which compressor is better suited for a specific tank capacity.

For a large aquarium (over 100 liters) use a piston compressor. For such an aquarium, it is better to take a device with low-voltage power (12 volts).

In the event of a power outage, it can be connected even with a car battery. You can make a quiet compressor using old equipment by yourself. So, in order for a home-made device to work as quietly as possible, you will need a wooden box and a box from under the film.

In this case, a quiet compressor is obtained by compensating the shock wave with a jar. The very same homemade compressor hides in a wooden box.

Also compressors are adjustable and not adjustable.

How to install a compressor in an aquarium?

Install the compressor in the aquarium is quite simple. First of all, it is necessary to determine the place where it will be located.

This may be the aquarium itself, a cover or a table. The device is placed on top of the water, or below the water level, but then a non-return valve is always installed on the air duct.

It is desirable that the aerator is located next to the heater. So the heating water will mix, and the conditions for the fish will be the best.

When the noise of a running compressor causes discomfort, it should be placed on foam or foam rubber. This will reduce the noise, but will not give 100% of the result.

Some act cardinally: put the device away and stretch a long hose. Any compressor needs to be cleaned periodically.

If this is not done, the performance will decrease and eventually the device will break. Also pollution increase the noise level.

The first type of pump delivers air through the movement of special membranes that allow air flow only in one direction. Such an aquarium compressor consumes very little electricity and operates with low noise.

The main disadvantage of this device is low power. Aerator is not suitable for large containers.

However, for example, for a 150-liter home aquarium, a small membrane silent compressor will fit perfectly.

Another type of aquarium aerators – piston compressors. From their name it follows that air is pushed out with the help of a piston.

These aerators are more expensive, but their advantage is high performance and durability.

True, the noise level of reciprocating compressors is somewhat higher than in devices of the first type. Such aerators are usually installed in large aquariums or columns.

Home aerators of both types are both powered by household electrical network, and from batteries. Each aerator kit includes a flexible hose from which pumped air comes out.

What is a battery-powered compressor used for?

There are situations when urgent transportation of fish is required. However, do not deprive the fish of such important oxygen for them. Otherwise, they may simply die.

You can use the road device for a small aquarium. Such equipment operates on batteries, which are very easy to replace at the right time. The battery-powered compressor allows you to protect against the death of fish that are outside the stationary aquarium.

Such equipment has small dimensions, so taking it with you on a trip is very convenient. A battery-powered device may also be necessary if the power is often cut off in the room.

Such a device is recommended to keep in reserve absolutely all aquarists. This is due to the fact that even short-term oxygen deprivation is fraught with fish for death. The question of how to choose a compressor, even experienced aquarists are asked.

Choosing a compressor you need to focus not on its price category, but on the amount of water that it can drive in one hour. It is desirable to acquire powerful silent compressors.

You can use a homemade device.

Required compressor capacity depending on the size of the aquarium

Compressor care, preventative maintenance

As an alternative to compressor You can offer an oxidizer. It is extremely simple in design and operation of the device. It does not require the supply of electricity or the installation of batteries, and it is absolutely silent because only chemical reactions occur in it.

The principle of operation of the oxidizer is the decomposition of hydrogen peroxide (H2O2) into water (H2O) and active oxygen (O), under the action of a catalyst. As a catalyst, there are metals that, when oxidized, take a part of the active oxygen, and the excess oxygen is released into the water.

read also mollies.

The compressor for the aquarium allows you to create comfortable conditions for the life of the fish. Before you choose this equipment, you need to understand why this device is necessary.

The compressor allows for additional aeration of water in the aquarium. It is necessary for containers of absolutely any size. Even small round aquariums are also equipped with modern quiet devices.

Thanks to this device you can save the health of fish. That is why the answer to the question of whether a compressor is needed in an aquarium is obvious.

The main requirements that must be placed on the device when choosing it

Often the aquarium is in the same room where people relax. Therefore, for the aquarium it is better to choose a silent compressor. This device operates continuously.

To reduce the noise level of the device, you can remove it into the cabinet. But then you need too long duct. Therefore, it is worth thinking carefully before making the compressor silent, by isolating it.

It is better to purchase a silent device at once. The air compressor for the aquarium is the most silent.

Compressors should have a smooth adjustment of the air flow. Such a device can be easily adjusted to a different number of filters and nozzles. Compressor capacity is calculated on the basis of the following parameters: 0.5 l / h per 1 l of water.

This is the way to solve the question of which compressor is better suited for a specific tank capacity. For a large aquarium (over 100 liters) use a piston compressor. For such an aquarium, it is better to take a device with low-voltage power (12 volts).

In the event of a power outage, it can be connected even with a car battery.

You can make a quiet compressor using old equipment by yourself. So, in order for a home-made device to work as quietly as possible, you will need a wooden box and a box from under the film. In this case, a quiet compressor is obtained by compensating the shock wave with a jar.

The very same homemade compressor hides in a wooden box.

Installing a compressor in an aquarium is a fairly simple task. Before you install the device in the aquarium, you must determine the place in which it will be located.

The device can be placed both in the aquarium itself (above the water) and in the lid or pedestal.

What type of compressor should be used for a round shaped aquarium?

Quite often, an aquarium is installed in the same room where people relax. Therefore, you need to select a silent air compressor. The fact is that the operation of this device is constant.

Of course, you can use a homemade compressor for an aquarium. For example, the compressor can be removed in the cabinet (which you will need to do beforehand). However, this presents certain difficulties.

So, in the case of the cabinet, you also need to make a rather long duct. That is why it is better to immediately acquire a silent internal device.

If you still decided to make a silent compressor for an aquarium with your own hands, then you should stock up on a box from under the film and a wooden box. With the help of the box, the shock wave is compensated, and the air compressor itself is hidden in the already mentioned cabinet – a box made of wood.

When choosing a device also take into account the presence of a smooth adjustment of the air flow. If this adjustment is, then you can easily adjust the internal compressor for any sprayer and filter.

When choosing, you must also consider the size. So, for large aquariums, the volume of which exceeds 100 liters, a two-channel piston compressor is used. It is better that the device be low-voltage (i.e.

12 volts). Why do you need it?

A piston device with a power of 12 volts can be connected even through a conventional car battery.

О admin

x

Check Also

Design elements of the aquarium – Stones, Shells, Snags

In most cases, the general aquarium contains fish originating from the natural environment, where rocks ...

Dry feed for aquarium fish

It is difficult and dangerous to feed aquarium fish with natural live food. The ecology ...

Dutch aquarium – creation and content

The aquarium, in the landscape of which the focus is on lush and dense thickets ...

Timer for aquarium

Caring for an aquarium is a constant and rather monotonous action, but the clearer their ...

Aquarium water filtration

The density of fish in home aquariums is usually higher than in natural waters. The ...

Aquaria yesterday and today

Aquaria – what exact and at the same time capacious word! Aqua – water;Riu – ...

Algae in the aquarium

Algae in the aquarium – This is probably one of the main problems aquarist. There ...

Equipment for the aquarium – part 2

Aquarium water treatment equipment This equipment is used to pump air through the water of ...

Aquarium fish food – 1 part

Pisces, like all other animals, need food to live, grow and reproduce. Food provides the ...

Choice of aquarium and installation – form, types, types

The shape and types of aquarium There are many varieties of aquariums. First of all, ...

Aquarium decoration in natural style – Aquascape Style

Aquarium decoration in a natural style or Aquascape / Aquascape Style. Aquascaping is an art ...

Natural composition in an aquarium

Natural composition in an aquarium Using plants, stones, gravel, snags and background in a single ...

Nano-aquarium – arrangement, launch, maintenance

Fashionable now the prefix “nano” is now used in aquarism. And not just used, but ...

Psevdomorskogo aquarium: rules design and care for him

If the interior design of your home is based on unusual and non-standard lines, what ...

My first acquaintance with the company DIAMIX and its product for aquariums

Good day, dear colleagues. In today’s article I would like to tell you how I ...

Diagnosing Aquarium Fish Disease – A Short Guide

Good day, dear colleagues. We continue to study the most common questions on aquarism, in ...

Handbook aquarist – Sergey Ermolaev

Good afternoon, dear readers! Today I decided to distract from writing articles about aquarium fish ...

Unforgettable Aquarium Design for Maze Fish

Labyrinth, or as they are called – Anabasovye, can breathe not only oxygen like other ...

Spawning behavior of cichlids: facts and assumptions

Quite often, one can hear from aquarists of various stripes that all cichlids, without exception, ...

Unusual design catfish aquarium – everyone will do it!

Hello, friends! Somiki are an indispensable attribute of almost any aquarium. Quite often, you can ...

Create an aquarium design for cichlids in the home pond

Hello, dear colleagues. I am glad to welcome you again on my blog and today ...

How important is oxygen in an aquarium and how to ensure it biotope

Good day, dear colleagues. glad to welcome you again on my blog. Today I want ...

Aquaria in Brazil – Fisheries

Dear colleagues! Today I will not talk about aquarium fish or plants. This post will ...

What is Paludarium and how to equip it at home

Hello, dear subscribers and readers Aquablog. The topic of today’s article will be called “Paludarium”. ...